Welch Allyn Propaq LT 802LT0N Скачать руководство пользователя страница 38

Страница: 38 / 80

Disassembly and reassembly

Welch Allyn Propaq LT Vital Signs Monitor

Disassembling the top chassis

The top chassis assembly contains the top plastic panel assembly (including the
integrated overlay for buttons, window, LEDs, and trim), the display module, and the
speaker.

“Removing the lithium ion battery assembly”

on page 29.

“Separating the top and bottom chassis halves”

on page 31.

Remove the display module.

Remove the four screws from the display bracket, and remove the bracket to free
the display module.

Remove the display module.

REASSEMBLY:

Tighten the display bracket screws to a torque of 2 inch lbs. Take care to avoid stripping
the plastic screw mounts.

Caution

Take care to protect the front surface of the display module and all

surfaces of the display screen from scratching and contamination.

Display module (back side)

Bracket

Bracket screws

REASSEMBLY: The display module cable lies under the bracket.

Reassembly: 2 inch lbs

Gaskets

Содержание Propaq LT 802LT0N

















































































Результаты поиска

Содержание Propaq LT 802LT0N

Отзывы:

Похожие инструкции для Propaq LT 802LT0N

Бренды по названию

Популярные бренды

Welch Allyn Propaq LT 802LT0N, Руководство по обслуживанию

Результаты поиска

Содержание Propaq LT 802LT0N

Отзывы:

Похожие инструкции для Propaq LT 802LT0N

Бренды по названию

Популярные бренды