Welch Allyn ELI 150 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 104

background image

Section 1

1-1

General

Service Manual Purpose

The purpose of this manual is to supply information to service personnel so they can maintain the ELI 150
Interpretive and Non-Interpretive Electrocardiograph at the assembly and subassembly level. Although the manual
includes parts lists, mechanical assembly parts, and printed circuit board information, it is intended to function
primarily as a guide to preventative and corrective maintenance and electrical repairs considered field repairable.

User Safety Information

Periodic Safety Inspections

Follow the recommended maintenance schedule. Inspect the power cord and transmission cables
periodically for fraying or other damage and replace as needed. Broken or frayed wires may cause
interference or loss of signal. Pay particular attention to points where wires enter connectors.

Proper Power Cord

Use only the power cord specified for the equipment. This product requires a three-wire, (18 gauge, SJT-
grade) power cord, which is supplied with a three-terminal, polarized plug (hospital grade) for connection
to the power source and protective ground. Use only a power outlet with a protective ground outlet. An
interruption of the grounding connection could cause an electrical shock hazard.

Proper Fuse

Use only the fuse specified for the equipment (identical in type, voltage and current rating). Substituting a
different fuse type could cause a fire hazard. Always make sure fuses have been installed before operating
the unit.

Do Not Operate in Explosive Atmospheres

Do not operate the ELI 150 in the presence of flammable gasses or anesthetics; this environment could
cause an explosion. Refer to Operator's Manual Safety Information: Warning(s) and Caution(s).

Use Only Safe Methods of Interconnection

To prevent electrical shock from the product when it is connected to other electrical equipment, proper
grounding is essential. Refer to Operator's Manual Safety Information: Warning(s) Peripheral equipment.

Do Not Mount Product above Patient

Do not mount or place the product where it could fall on a patient or where it could be accidentally knocked
off a shelf or other mounting arrangement.

Recommended Accessories

For the patient's safety and optimum equipment performance, use only the accessories specified by Mortara
Instrument, Inc.

1

«
...
13
14
15
16
17
...
»

Содержание ELI 150









































































































Отзывы:

Нет отзывов

Похожие инструкции для ELI 150

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: ABB Страницы: 4

ARCHISHAPE 2.0 Linear

Бренд: Osram Страницы: 7

Бренд: Mindray Страницы: 295

Бренд: ZAMST Страницы: 14

TRACER pH PockeTester 1741

Бренд: LaMotte Страницы: 16

Бренд: Psiber Страницы: 16

Бренд: XPOtool Страницы: 4

Бренд: Harken Страницы: 78

Add-It AFI 5016-H

Бренд: DIG Страницы: 2

Бренд: Electro-Music Страницы: 120

Бренд: Martin Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды