Welbilt Manitowoc U65 Скачать руководство пользователя страница 19

Part Number 040006019 07/18

4-1

Section 4

Maintenance

Interior Cleaning and Sanitizing

GENERAL

Clean and sanitize the ice machine every six months for 
efficient operation. If the ice machine requires more 
frequent cleaning and sanitizing, consult a qualified 
service company to test the water quality and 
recommend appropriate water treatment.

The ice machine must be taken apart for cleaning and 
sanitizing.

CLEANING AND SANITIZING PROCEDURE

Ice machine cleaner is used to remove lime scale and 
mineral deposits. Ice machine sanitizer disinfects and 
removes algae and slime.

step 1  

Set the toggle switch to the OFF position after 

ice falls from the evaporator at the end of a Harvest 
cycle. Or, set the switch to the OFF position and allow 
the ice to melt off the evaporator.

step 2  

Remove all ice from the bin.

step 3  

To start a cleaning cycle, move the toggle switch 

to the WASH position.

step 4  

Wait until water flows over the evaporator (about 

three minutes) then add the proper amount of 
Manitowoc Ice Machine Cleaner to the water trough.

step 5  

Wait until the clean cycle is complete 

(approximately 45 minutes) then place the toggle switch 
in the OFF position, disconnect power and water 
supplies to the ice machine.

step 6  

Remove parts for cleaning.

A. Remove the Overflow Tube

To remove the tube, lift it up while using a 
slight back and forth motion to loosen it from 
the drain hole.

When installing the tube, be sure it is completely 
inserted into the drain hole to prevent water leakage 
during normal operation.

Removing the Overflow Tube

B. Remove the Vinyl Hose

!

Caution

Use  only  Welbilt  approved  Ice  Machine  Cleaner
(part  number  94-0546-3)  and  Sanitizer  (part
number 94-0565-3). It is a violation of Federal law
to use these solutions in a manner inconsistent with
their  labeling.  Read  and  understand  all  labels
printed on bottles before use.

!

Caution

Do  not  mix  Ice  Machine  Cleaner  and  Sanitizer
solutions together. It is a violation of Federal law to
use  these  solutions  in  a  manner  inconsistent  with
their labeling.

!

Warning

Wear rubber gloves and safety goggles (and/or face
shield)  when  handling  Ice  Machine  Cleaner  or
Sanitizer.

!

Caution

Never use anything to force ice from the evaporator.
Damage may result.

Model

Amount of Cleaner

U65

45 ml

!

Warning

Disconnect electric power to the ice machine at the
electric switch box before proceeding.

DRAIN

HOLE

OVERFLOW 

TUBE

Содержание Manitowoc U65



























Отзывы: