Welbilt Manitowoc U65 Скачать руководство пользователя страница 12

Installation Instructions

Section 2

2-2

Part Number 040006019 07/18

Location of Ice Machine

The location selected for the ice machine must meet the 
following criteria. If any of these criteria are not met, 
select another location.

The location must be indoors.

The location must be free of airborne and other 
contaminants.

The air temperature must be at least 10

C (50

F), but 

must not exceed 40

C (110

F).

The location must not be near heat-generating 
equipment or in direct sunlight. 

The location must be capable of supporting the 
weight of the ice machine and a full bin of ice.

The location must allow enough clearance for water, 
drain and electrical connections in the 

rear of the ice 

machine.

The location must not obstruct airflow through or 
around the ice machine (condenser airflow is in and 
out the front). Refer to the chart below for clearance 
requirements.

NOTE: The ice machine may be built into a cabinet.

There is no minimum clearance requirement for the top 
or left and right sides of the ice machine. The listed 
values are recommended for efficient operation and 
servicing only.

Ice Machine Heat of Rejection

  *

B.T.U./Hour

**

Because the heat of rejection varies during the ice making 
cycle, the figure shown is an average.

Ice machines, like other refrigeration equipment, reject 
heat through the condenser. It is helpful to know the 
amount of heat rejected by the ice machine when sizing 
air conditioning equipment where self-contained air-
cooled ice machines are installed.

Leveling the Ice Machine

After moving the ice machine into the installation 
location, it must be leveled for proper operation. Follow 
these steps to level the ice machine:

1. Check the level of the ice machine from front to back 

and from side to side.

Checking for Level

2. If the ice machine is not level, adjust the leveling 

glides on each corner of the base of the ice machine 
as necessary.

Leveling Glide

3. Check the level of the ice machine after each 

adjustment of the leveling glides.

4. Repeat steps 2 and 3 until the ice machine is level 

from front to back and from side to side.

Self-Contained Air-Cooled

Top/Sides

5” (127 mm)*

Back

5” (127 mm)*

!

Caution

The  ice  machine  must  be  protected  if  it  will  be
subjected  to  temperatures  below  32

F  (0

C).

Failure  caused  by  exposure  to  freezing
temperatures  is  not  covered by  the  warranty.  See
“Removal from Service/Winterization” Section 4.

Series

Ice Machine

Heat of Rejection*

Air Conditioning**

Peak

UDE0065A

1600

2350

Содержание Manitowoc U65



























Отзывы: