Welbilt Convotherm mini black easyTouch 10.10 Скачать руководство пользователя страница 19

Страница: 19 / 148

Requirements concerning the combi oven's surroundings

Required combi oven surroundings

■

Ambient temperature between 40°F and 95°F

■

No toxic or potentially explosive atmospheres

■

Do not use or store gasoline or other flammable vapors, gases, or liquids in the vicinity of a combi

oven

■

Dry kitchen floor in order to reduce the risk of accidents occurring

Required installation location characteristics

■

NO fire alarms or sprinkler system directly above the unit

■

NO flammable materials, gases, or liquids above, on, under, or close to the unit

Limitations on use

■

When used outdoors, the unit must be protected from rain and wind

■

Do NOT shift or move the unit during operation

Prerequisites for cleaning

■

Only use the cleaning agents approved by the manufacturer.

■

Do NOT use a pressure washer to clean the unit.

■

Do NOT use a water jet to clean the outside of the unit. Do not use a water jet for anything other

than cleaning the oven cavity.

■

Do NOT use bases or acids to clean the combi oven and make sure it is not exposed to acid

fumes. The only exception is when the oven cavity and the boiler are descaled by an authorized

service company following the manufacturer's instructions.

3 For Your Safety

Installation Manual

Содержание Convotherm mini black easyTouch 10.10





















































































































































Результаты поиска

Содержание Convotherm mini black easyTouch 10.10

Отзывы:

Похожие инструкции для Convotherm mini black easyTouch 10.10

Бренды по названию

Популярные бренды

Welbilt Convotherm mini black easyTouch 10.10, Руководство по установке

Результаты поиска

Содержание Convotherm mini black easyTouch 10.10

Отзывы:

Похожие инструкции для Convotherm mini black easyTouch 10.10

Бренды по названию

Популярные бренды