manualshive.com logo in svg

WEISS ROBOTICS CLG Series, Монтаж и эксплуатация, Страница: 28 / 58

Поделиться
Скачать
WEISS ROBOTICS CLG Series Скачать руководство пользователя страница 28

28- 

 

The recommended minimum gripping force is 25% of the nominal gripping force. If you need 

to grip your workpiece with a lower gripping force, please run suitable tests with your applica-

tion-specific fingers mounted. Keep batch variations in mind. If in doubt, discuss your applica-

tion with our technical support team. 

Address 

Grip Preset: Index 0x0060, Subindex 0x03 

Grip Preset: Index 0x0061, Subindex 0x03 

Data type 

UIntegerT(8) 

Factory setting 

see Table 12 

Example:  

Gripping with nominal gripping force: Set the value to 100 

Gripping with minimum gripping force 

6

: Set the value to 25 

8.2.2.3

 

Diagnostic Parameters  

Duration of the last successful gripping operation 

Returns the duration of the last successful gripping operation in milliseconds.  

Address 

Index 0x00A0, Subindex 0x01 

Data type 

UIntegerT(16) 

Factory setting 

(not available) 

Example:  

The last gripping operation took 42 ms. Reading the parameter returns the value 42. 

Duration of the last successful release operation 

Returns the duration of the last successful release operation in milliseconds.  

Address 

Index 0x00A0, Subindex 0x02 

 

6

 The recommended value for the minimum gripping force is 25%. See chapter 5.1.2. 

Содержание CLG Series



























































Отзывы:

Нет отзывов