manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Поделиться
Скачать
Weishaupt WTC-GB 15-B Compact Скачать руководство пользователя страница 85

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

85-196

6.6.6.2 Legionella protection

Domestic hot
water

 

 

Legionella
protection

Parameters

Setting

7.2.1
Protection function

Protection function against legionella.

Off:

Legionella protection deactivated.

By weekday

:

legionella protection is carried out on the weekday set, see parameter

 weekday

.

In intervals

:

legionella protection is carried out in intervals, see parameter

 interval

.

7.2.2
Start time

Time for the start of Legionella protection.

7.2.3
Weekday

Weekday on which Legionella protection is carried out.

Only if parameter

 protection function 

is set to

 by weekday 

.

7.2.4
Interval

Days until the next legionella protection is carried out.

Only if parameter

 protection function 

is set to

 in intervals 

.

7.2.5
Heat-up temperature
DHW

DHW setpoint temperature for Legionella protection.

7.2.6
Circulation for
legionella protection

Configure circulation pump for legionella protection.

Off

:

Circulation pump not activated during legionella protection.

On during legionella protection

:

Circulation pump is activated during legionella protection.
Disadvantage: if the pipework is long this setting leads to high heat loss.

On after legionella protection

:

Circulation pump activated for 4 minutes only after legionella protection.
Disadvantage: if the pipework is long this setting leads to high heat loss.

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды