Weishaupt WTC-GB 15-B Compact Скачать руководство пользователя страница 82

Страница: 82 / 196

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

82-196

6.6.5.4 Screed program

Heating
circuits

Screed
program

CAUTION

Damage to the building structure

It is possible that the screed program on the pump heating circuit could be masked
by other heating circuits or by DHW circuits.

If necessary, deactivate other heating or DHW circuits.

The screed program is used for the drying of underlay flooring and is separated into
two functions. Observe the requirements provided by the speed manufacturer
andEN 1264-4.

Function specific heating

First phase of drying. The function specific heating is used to ensure defect-free
preparation for underfloor heating.

Screed drying

Second phase of drying. Screed drying is used to continue drying ready for floor
covering work.

Содержание WTC-GB 15-B Compact





































































































































































































Результаты поиска

Содержание WTC-GB 15-B Compact

Отзывы:

Бренды по названию

Популярные бренды

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WTC-GB 15-B Compact

Отзывы:

Бренды по названию

Популярные бренды