manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Weishaupt WTC-GB 15-B Compact - Компактный газовый котел с инструкцией по монтажу и эксплуатации. Можно скачать бесплатно на manualshive.com для получения руководства пользователя. Удобное решение для вашего дома.

Поделиться
Скачать
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

7 Commissioning

83309302 1/2018-05 La

117-196

7.3 Check soundness of flue gas system

For room air independent operation, the soundness of the flue gas system must be
checked by means of an O

2

 measurement.

Guide the hose 

2

 via the measuring point in the supply air annular gap 

1

 into

the appliance.
Seal the measuring point in the supply air annular gap.
Connect the measuring probe 

3

 to the hose.

Mount the front panel.
Activate chimney sweep function.
Carry out O

2

 measurement at maximum load.

Adhere to a measuring period of at least 5 minutes.

It is admissible for the O

2

 content to fall short of the measured values of the ambi-

ent air by 0.2 % at the most.

1

3

2

7.4 Adjust capacity

Maximum load

If required, the maximum load can be changed via parameter 

 2.1.2 Maximum

load heating mode 

, see [ch. 6.6.2.1].

Minimum load

If required, the minimum load can be changed via parameter

 2.3.4 Correct

minimum load

, see [ch. 6.6.2.3].

Flue gas pipe length

The capacity adjustment for the flue gas pipe length is set via parameter

2.3.3 Correction speed for flue gas length

, see [ch. 6.6.2.3].

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

Watson-Marlow 120 Installation, Operating And Maintenance Manual preview
120
Бренд: Watson-Marlow Страницы: 55
Danfoss Heat Pump Troubleshooting Manual preview
Heat Pump
Бренд: Danfoss Страницы: 34
Danfoss DHP-H Installation Instructions Manual preview
DHP-H
Бренд: Danfoss Страницы: 52
Oceanic OCEACV100IFW2 Instructions Manual preview
OCEACV100IFW2
Бренд: Oceanic Страницы: 201
York E4TS030 Owner'S Manual preview
E4TS030
Бренд: York Страницы: 4
S&P SAHARA Series Installation Manual. Instructions For Use preview
SAHARA Series
Бренд: S&P Страницы: 18
Waterous S200-P Series Operation And Maintenance Instructions preview
S200-P Series
Бренд: Waterous Страницы: 10
Pfeiffer Vacuum MVP 020-3 AC Operating Instructions Manual preview
MVP 020-3 AC
Бренд: Pfeiffer Vacuum Страницы: 46
Zibro Laser FF 55 Operating Instructions Manual preview
Laser FF 55
Бренд: Zibro Страницы: 24
Accorroni RPE-HPE X 58 Technical Manual preview
RPE-HPE X 58
Бренд: Accorroni Страницы: 29
Lamborghini Caloreclima RUBINO M Use And Maintenance Manual preview
RUBINO M
Бренд: Lamborghini Caloreclima Страницы: 62
FLOJET 4305-144 Instruction Manual preview
4305-144
Бренд: FLOJET Страницы: 4
Wilo SiFire EN 100/200-205-45 E Installation And Operating Instructions Manual preview
SiFire EN 100/200-205-45 E
Бренд: Wilo Страницы: 108
L.B. White Pilot Light Ignition Installation And Service Manual preview
Pilot Light Ignition
Бренд: L.B. White Страницы: 21
DAB 50/9 Instruction For Installation And Maintenance preview
50/9
Бренд: DAB Страницы: 52
Easylife 2778 Instruction Manual preview
2778
Бренд: Easylife Страницы: 3
Franklin Electric Little Giant 16 G Series Owner'S Manual preview
Little Giant 16 G Series
Бренд: Franklin Electric Страницы: 36
KIRLOSKAR KOSN Series Installation, Operation & Maintenance Manual preview
KOSN Series
Бренд: KIRLOSKAR Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды