manualshive.com logo in svg

Weishaupt WHI sol/aqua 20 1, Руководство пользователя, Страница: 6 / 36

Поделиться
Скачать
Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 6

 

 

 

Installation and operation instructions 

Separation station WHI sol/heat 20 #1 / 40 #1; Separation station WHI sol/aqua 20 #1 / 40 #1

 

 

 

 

 

  2 Safety 

 

83514202 

▪ 

1/2014-06 

▪

 Ext. PAW

 

6-36 

 

 

CAUTION 

Personal injuries and material damage due to overpressure! 
Closing both ball valves in the primary circuit will separate the 

safety group from the heat exchanger. Heating the storage tank 

may result in high pressures, which may lead to personal injury 

and material damage!  

 

The ball valves may only be closed by skilled personnel 

when service is required, after the system has been 

switched off. When the system is recommissioned, all 

locks must be opened again. 

NOTICE 

Material damage due to mineral oils! 
Mineral oil products cause permanent damage in the material, 

resulting in its sealing characteristics getting lost.  

We cannot be held liable for damage caused by seals damaged in 

this way, and nor will we give warranty replacement for such 

parts.  

 

It is imperative to prevent the EPDM from making contact 

with substances containing mineral oils.  

 

Use a silicone- or polyalkylene-based lubricant free of 

mineral oil such as Unisilikon L250L and Syntheso  

Glep 1 from Klüber or a silicone spray.

 

 

In sunlight the collectors will heat up considerably.  

The solar fluid in the solar circuit may heat up to more than  

100 °C. 
Flush and fill the solar circuit only when the collector temperatures 

are below 70 °C. 

NOTICE 

Material damage due to high temperatures! 
Since the solar fluid near the collector can be very hot, the group 

of fittings must be installed at a sufficient clearance from the  

collector field. It may be necessary to install an intermediate tank 

in order to protect the expansion tank. 

 

 

2.3

 

Safety measures 

 

  Immediately eliminate safety-relevant defects and replace safety-relevant components 

when they have reached the end of their service life due to their construction. 

 

 

2.4

 

Electrical connection 

 

  When performing any work on live parts: 

Observe the accident prevention regulations BGV A3 and local regulations, 

Use tools according to EN 60900. 

 

 

2.5

 

Structural modifications 

 

  Conversion measures are only allowed after prior approval in writing by the  

Max Weishaupt GmbH. 

Additional components may only be installed if they were not tested together with the 

machine. 

Use only Weishaupt original parts. 

 

 

2.6

 

Disposal 

 

  Dispose of the materials used properly and in an environmentally compatible manner.  

In doing so, observe local regulations. 

Содержание WHI sol/aqua 20 1





































Отзывы:

Нет отзывов