Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 16

Installation and operation instructions

Separation station WHI sol/heat 20 #1 / 40 #1; Separation station WHI sol/aqua 20 #1 / 40 #1

4 Installation

83514202

▪

1/2014-06

▪

Ext. PAW

16-36

4.2

Hydraulic connection

1.

Pipe the separation station with the system according to the diagram below.

Pipe gap from the wall

(primary) = 95 mm

Pipe gap from the wall

(secondary) = 167 mm

1

Primary side: supply from collector
Connection:
WHI sol/heat and sol/aqua 20 #1: ¾" female thread
WHI sol/heat and sol/aqua 40 #1: 1" female thread

2

Primary side: return to collector
Connection:
WHI sol/heat and sol/aqua 20 #1: ¾" female thread
WHI sol/heat and sol/aqua 40 #1: 1" female thread

3

Secondary side: return from buffer tank (cold)
Connection:
WHI sol/heat 20 #1: ¾" female thread
WHI sol/aqua 20 #1: 1" male thread, flat sealing
WHI sol/heat 40 #1: 1" female thread
WHI sol/aqua 40 #1: 1¼" male thread, flat sealing

4

Secondary side: supply to buffer tank (hot)
Connection:
WHI sol/heat 20 #1: ¾" female thread
WHI sol/aqua 20 #1: 1" male thread, flat sealing
WHI sol/heat 40 #1: 1" female thread
WHI sol/aqua 40 #1: 1¼" male thread, flat sealing

2.

Assemble the safety group consisting of safety valve [c], fill valve [d] and

pressure gauge [e] on the connection of the return ball valve [b].

3.

Connect the expansion tank below the pressure gauge [e].

For service work on the expansion tank, we recommend assembling a cap

valve on the expansion tank.

NOTICE

Note regarding the expansion tank
The expansion tank must not be connected while flushing and

filling in order to prevent dirt particles from being flushed in.

4.

Adapt the initial pressure of the expansion tank to the system and connect the

expansion tank. Observe the separate instructions for the expansion tank!

5.

Check all screw connections and retighten them, if necessary.

«
...
14
15
16
17
18
...
»

Содержание WHI sol/aqua 20 1





































Отзывы:

Нет отзывов