Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 14

Installation and operation instructions

Separation station WHI sol/heat 20 #1 / 40 #1; Separation station WHI sol/aqua 20 #1 / 40 #1

4 Installation

83514202

▪

1/2014-06

▪

Ext. PAW

14-36

4

Installation

4.1

Assembly

The installation site must be dry, stable and frostproof. Furthermore, access to the

controller and safety equipment must be guaranteed at all times during operation!
The discharge line of the safety equipment should be guided into heat-resistant

collection tanks of suitable size. This prevents uncontrolled discharging into the

environment and enables the circuits to be refilled!
Due to their construction, the WHI sol/aqua modules reduce the precipitation of scale in

the heat exchanger. For systems with a high total domestic water hardness and/or high

temperatures, a water treatment is recommended, in order to prevent scale formation.

NOTICE

Material damage due to high temperatures!
Since the solar fluid near the collector can be very hot, the group

of fittings must be installed at a sufficient clearance from the

collector field.

It may be necessary to install an intermediate tank in order to

protect the expansion tank.

Separation station WHI sol/heat 20 #1

Separation station WHI sol/heat 40 #1

«
...
12
13
14
15
16
...
»

Содержание WHI sol/aqua 20 1





































Отзывы:

Нет отзывов