Weishaupt W-FM 25 Скачать руководство пользователя страница 52

Страница: 52 / 72

6.4.2 Adjusting oil side

1. Preset combustion manager

▶

Set fuel selection switch to OIL.

▶

Unplug bridging plug No. 7 on combustion manager.

▶

Switch on voltage supply.

✓

The unprogrammed condition of the combustion manager is indicated by a flashing

display.

The burner goes to lockout.

▶

Press [ENTER] key.

✓

Burner has been reset.

✓

Combustion manager drives to Standby.

Parameters

and

must be set to value

▶

Press [Enter] and [+] keys simultaneously for approx. 2 seconds.

✓

The parameter level is activated.

▶

Press [+].

▶

Press [Enter] key until parameter

is displayed.

▶

Set parameter

(oil pressure switch) to value

(activated).

▶

Press [Enter] key.

▶

Set parameter

(air pressure switch) to value

(activated).

▶

Press [Enter] key until parameter

OFFUPr

is displayed again.

▶

Press [G] and [L/A] simultaneously.

✓

Combustion manager changes to access level.

▶

Press [+].

✓

Setting level (parameter

) is displayed.

▶

Set value

(dual fuel burners) using [ENTER] and [+] key.

▶

Press [+].

✓

is displayed.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

6 Commissioning

83294002 • 2/2014-11 • La

52-70

Содержание W-FM 25









































































Результаты поиска

Содержание W-FM 25

Отзывы:

Бренды по названию

Популярные бренды

Weishaupt W-FM 25, Руководство пользователя

Результаты поиска

Содержание W-FM 25

Отзывы:

Бренды по названию

Популярные бренды