manualshive.com logo in svg

Weishaupt W-FM 25, Руководство пользователя

Поделиться
Скачать
Weishaupt W-FM 25 Скачать руководство пользователя страница 42

6.3 Oil burner

1. Preset combustion manager

▶

Unplug bridging plug No. 7 on combustion manager.

▶

Switch on voltage supply.

✓

The unprogrammed condition of the combustion manager is indicated by a flashing

display.

The burner goes to lockout.

▶

Press [ENTER] key.

✓

Burner has been reset.

✓

Combustion manager drives to Standby.

If an oil pressure switch is fitted, set parameters 

7

 and 

8

 to 1 (see Ch. 4.2.3.3).

If an air pressure switch is fitted, set parameter 

8

 to 1 (see Ch. 4.2.3.3).

▶

Press [G] and [L/A] simultaneously.

✓

Combustion manager changes to access level.

▶

Press [+].

✓

Setting level (parameter 

E0

) is displayed.

▶

Adopt value 

0

 (single fuel burner), if necessary adjust using [ENTER] and [-] key.

▶

Press [+].

✓

E1

 is displayed.

The value of parameter 

E1

 can not be altered.

▪

0

 = intermittent operation (Standard)

▪

1

 = continuous operation (only if W-FM 21was used previously)

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

6 Commissioning

83294002 • 2/2014-11 • La

42-70

Содержание W-FM 25









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды