Weishaupt W-FM 25 Скачать руководство пользователя страница 31

Страница: 31 / 72

Fitting W-FM 25

On sizes W30 and W40, the burner motor should be fed via contactor (except when

using variable speed drive).

If the boiler control is protected by an internal 10 A fuse, the plug cable for separate

motor power supply can be used. This means it is not necessary to install a separate

voltage supply for the motor.

Pre-fusing of separate supply line:

▪

min 10 AT

▪

max 16 AT

▶

Observe inputs and outputs of combustion manager W-FM 25 (see Ch. 3.1).

▶

If required, remove contactor and snap it on to the carrier rail

of the bracket

supplied.

▶

If required, fit bracket

supplied.

▶

Fit combustion manager.

▶

Plug in all plugs, if necessary use extension cable No. 4.

▶

On gas and dual fuel burners, plug in bridging plug No. 15 supplied

(see Ch. 3.1).

▶

If necessary, connect supply line for burner motor or plug cable for motor voltage

supply to the connection plug of the contactor.

W10/20

W30/40

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

5 Installation

83294002 • 2/2014-11 • La

31-70

Содержание W-FM 25









































































Результаты поиска

Содержание W-FM 25

Отзывы:

Бренды по названию

Популярные бренды

Weishaupt W-FM 25, Руководство пользователя

Результаты поиска

Содержание W-FM 25

Отзывы:

Бренды по названию

Популярные бренды