manualshive.com logo in svg

Weinmann MEDUMAT Easy CPR, Инструкции по обслуживанию и ремонту

Поделиться
Скачать
Weinmann MEDUMAT Easy CPR Скачать руководство пользователя страница 53

Technical data

53

9.1  Pneumatic / electronic systems

The input pressure at p is max. 6bar. This is dynamically reduced by V1 to 2.5 bar. This is the input pressure 
at V2, V3 and V4.

Inspiration

An electrical impulse to V2 opens V3 and closes V4. Oxygen flows through the ventilation hose to the patient 
valve. If the ventilation pressure in the patient valve reaches >100 mbar, the relief valve V5 will open.

Expiration

A fresh electrical impulse closes V2. The relief valve V4 opens and vents the ventilation hose. The patient 
breathes out through the patient valve.

Demandflow

An inspiration impulse (trigger) at V2 opens valves V3 and V4.

Electronic system

The microprocessor-controlled electronic system sets the ventilation parameters and monitors ventilation, and 
also O

2

 supply and power supply. If necessary, a visual and acoustic alarm is given. The ventilator has an 

audio response facility that can be switched on for user guidance.

Patient valve

During inspiration the ventilation gas flows to the patient.

During expiration the expiration pressure switches the valve so 
that the patient can breathe out.

Содержание MEDUMAT Easy CPR





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды