上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
.
57
/
116
Follow the steps below to help troubleshoot:
Modify the encoder direction parameter and see if the alarm disappears.
If not, undo the encoder direction modification and modify the axis rotation direction.
If both the axis direction and encoder direction are incorrect, reverse both the
encoder direction and axis rotation values.
4.4.9 Follow In-position Waiting Timeout
Reason
The value of
INposition Tolerance
is too small.
Calibration data error.
Influence of external slag discharge during machining.
Follow overshooting.
Solution
Follow the steps below to help troubleshoot:
Check the
INposition Tolerance
value.
The recommended value is 0.1.
Execute Execute Calibration again.
Adjust the cutting technic settings.
Check the follow parameters and drive parameter settings.
Ensure that they are set correctly.
4.4.10 Large Follow Error Alarm
Reason
Within a certain period of time, the follow error is larger than the out-of-edge tolerance
setting.
Solution
Follow the steps below to help troubleshoot:
If this alarm was reported when the material surface is quite flat, it may have been
caused by follow overshooting. In this case, check the servo drive gain value.
If the value is too small, increase it as needed.
If this alarm was reported during cutter lifting, the follow gain value may have been
too small.
4.4.11 System Reports Material Collision Alarm when Follow is Enabled in Idle Status or
During Machining
Reason
The current capacitance is equal to or smaller than the
Touch Part Capacitance
value.
Solution
Follow the steps below to help troubleshoot:
1. Set
Touch Part Capacitance
to a proper value.
It is recommended that you use the default value (0).
2. If the alarm is reported when enabling the follow function:
a. Ensure that
Pulse Equivalent
,
Feedback Pulse Count
,
Speed Gain
are set
correctly.
b. Ensure that the drive gain parameter is set correctly.
3. If the alarm is reported during machining:
a. Ensure that there is no exception under manual following.
Содержание LS6000M
