-7 -
3) The collar will return to its original position
when it is released.
4) Pull the bit to make sure it does not come out.
5) To remove the bit, pull out the collar in the
same way.
Bit
Hexagonal bit chuck
9.5 mm (3/8”)
- 13 mm (33/64”)
6.35 mm (1/4”)
•
Clutch Handle
(Clutch Torque Setting)
Adjust the torque to one of the 21 possible
settings to the job. There is an interval of
about 0.13 N·m (
1.3 k f-cm or 1.1 in-lbs)
between steps.
CAUTION:
Test the setting before actual operation.
Set the scale at this mark.
Reference for Adjusting Torque
Setting
Torque
Use
1
Approx: 0.36 N·m
(3.7 kgf-cm or 3,2 in-lbs)
For driving
screws
5
Approx: 0.80 N·m
(8.2 kgf-cm or 7.0 in-lbs)
9
Approx: 1.20 N·m
(12.2 kgf-cm or 10.6
in-lbs)
13
Approx: 1.67 N·m
(17.0 kgf-cm or 14.8
in-lbs)
17
Approx: 2.26 N·m
(23.0 kgf-cm or 19.8
in-lbs)
21
Approx: 2.83 N·m
(28.6 kgf-cm or 25.0
in-lbs)
Approx: 4.4 N·m
(45.0 kgf-cm or 39.0
in-lbs)
For power-
ful driving
screws
and drilling
• When using at high speeds, set the
clutch at 10 or below. (Operation stops
at the maximum torque of 1.5 N·m (15
kgf-cm) when the scale is higher.)
• The auto shut-off function may become
inoperable at high clutch settings when
battery power drops. Recharge the bat-
tery in that case.
NOTE:
The chart is only a reference. The torque
settings may differ by materials, types of
screws, etc. Pleae test it at your own
conditions before use.
•
Battery Low Warning Lamp
Excessive (complete) discharging of Li-
ion batteries shortens their service life
dramatically. The driver includes a battery
protection feature designed to prevent
excessive discharging of the battery pack.
• The battery protection feature activates
immediately before the battery loses its
charge, causing the battery low warning
lamp to flash.
• If you notice the battery low warning
lamp flashing, charge the battery pack
immediately.
•
Using the LED Light
Before the use of LED light, always pull the
power switch once.
Press
the LED light on button. The
light illuminates with very low current, and
it does not adversely affet the performance
of the tool during use or its battery capacity.
<Battery low warning lamp>
Off (normal
operation)
Flashing
(No charge)
Battery protection
feature active
Содержание DMS PRO 1479120000
