Troubleshooting
2518100000/03/06.2017
48
8.3 Replacing the stripping blades
WARNING
Potential risk of fatality due to electric
shock
When working on the inside of the machine,
non-insulated parts may be touched.
► Switch the machine off.
►
Remove the compressed air hose from the
compressed air source.
►
Pull the power plug.
►
Open the front plate and place it down
carefully.
CAUTION
Risk of injury posed by sharp blades
►
Use forceps to change the blades.
►
Dispose of the removed blades in a sepa-
rate container.
All present blades must be replaced each time
the knife is changed.
1
2
Figure 8.1 Stripping unit
►
Remove both eccentrics (
1
) (2.5 mm Allen key).
► Release the fixing screws (
2
) (2.0 mm Allen key) and
remove the cover.
►
Replace all present blades with new ones.
Figure 8.2 Blade alignment
►
L and LS
: Assemble each blade pair so that the bevelled
edges point outwards (marked in red in figure 8.2).
Place both blade pairs in the holder.
►
LZ
: inset the blades so that the bevelled edges point to-
ward each other.
►
Fix the cover back on.
►
Fix both eccentrics so that they are in position "0".
►
Conduct a stripping test (see section 5.5).
8.4 Replacing fuses
► Make sure that the machine is switched off.
►
Remove the power plug.
1
Figure 8.3 Opening the fuse compartment
►
Lever the fuse compartment (
1
) out of the mains filter
unit using a slotted screwdriver.
►
Replace both fuses with new ones (2 x T2AH250V).
► Put the fuse compartment back into the mains filter unit.
L, LS
LZ
Содержание 1243790000
