WEICHAI WP6GTA Скачать руководство пользователя

Страница: 9 / 90

Weichai America Corp.

Disassembling:

Use dedicated tool to disassemble the camshaft sleeve, and try to protect other sleeves during

disassembling.

Inspection:

Before assembling, grease on sleeve back, bush surface and fitting hole inner surface must be

wiped out, and make sure there is no burr, overlap and scrap iron.

Assembling:

Apply oil on engine block hole, put camshaft sleeve into the dedicated tool and guide it into

engine block, in the meantime align oil gallery holes on the sleeve and engine block.

Key point 3:

Assembly: Install the greased seal ring to the welded elbow, insert the elbow into the

corresponding hole, and fix it on the engine block by using a fixing plate, hexagon socket bolts

and spring washers.

2.2

Steps to Assemble and disassemble Engine Block Module

2.2.1 Exploded View of Engine Block Module

Содержание WP6GTA



























































































Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды

WEICHAI WP6GTA, Руководство по сборке/разборке

Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды