WEICHAI WP6GTA Скачать руководство пользователя

Страница: 26 / 90

Weichai America Corp.

4. Cylinder head gasket:

If there is air leakage, water leakage or oil leakage in cylinder head gasket, then the gasket should

be checked and replaced; Check the gasket for visible damage and analyze the cause, cylinder

cover gaskets are disposable, and should be replaced during maintenance.

2.10

Cylinder Head Cover Assembly and Disassembly

2.10.1 Cylinder Head Cover Exploded View

Fig. 2-20 Exploded view of cylinder head cover

No.

name

No.

name

bolt

Cylinder head cover

washer

Cylinder head cover gasket

2.10.2 Cylinder Head Cover Disassembly Procedure

Loosen the cylinder head cover bolts. Remove the bolts and the washers.

Pull the covers up vertically to remove them. Remove all gaskets.

2.10.3 Cylinder Head Cover Assembly Procedure

Use new cylinder head cover gaskets for all assemblies and inspect them for any defects or

damage prior to assembly.

Содержание WP6GTA



























































































Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды

WEICHAI WP6GTA, Руководство по сборке/разборке

Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды