WEICHAI WP6GTA Скачать руководство пользователя

Страница: 21 / 90

Weichai America Corp.

2.8

Assembly and disassembly of oil sump.

4.2.8.1 Exploded view of oil sump.

Fig. 2-15 Exploded view of oil sump

2.8.2 Steps to disassemble oil sump.

Turn over engine to keep oil sump upward (key point 1)

Remove fixing bolts of oil sump.

Remove oil sump.

Remove the combination gasket and magnetic screw plug assembly

2.8.3 Steps to assemble oil sump.

Assembling steps are contrary to disassembling ones.

2.8.4 Inspection and maintenance of oil sump.

Key point 1:

Disassembling

Before the disassembling, all engine oil should be drained out. Put an engine oil container under

drain screw plug of oil sump, screw off the plug with a plug wrench to drain oil out.

Key point 2:

bolt

plug seat

seat

washer

oil pan

seat seal

washer

magnetic

plug

Содержание WP6GTA



























































































Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды

WEICHAI WP6GTA, Руководство по сборке/разборке

Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды