WEICHAI WP10 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 53

background image

Operation and Maintenance Manual and User Service Guide for Industrial Power WP10 Series Diesel Engine

20

4. Maintenance specifications for industrial engines

Maintenance intervals and specifications of industrial engines are suitable for
P4, P6, 10L, 12L, 13L and Baudouin series.

4.1 Maintenance intervals and specifications of industrial engines

4.1.1 Maintenance intervals of industrial diesel engines

Initial maintenance ( P ) New engine running for 30-50h

Level 1 maintenance (WD1) Diesel engine running interval 250h

Level 2 maintenance (WD2) Diesel engine running interval 500h

Level 3 maintenance (WD3) Diesel engine running interval 1000h

Level 4 maintenance (WD4) Diesel engine running interval 3000h

4.1.2 Daily maintenance for diesel engine

4.1.2.1 With diesel engine running, always note that the oil temperature, oil

pressure and coolant temperature at outlet, and check for “three

-

leakage”

(oil, gas and water). In case of any abnormal, find out the cause for
troubleshooting.

4.1.2.2 After the diesel engine is stopped, check the fuel, fresh-water coolant

and oil capacity, if needed, refill it.

4.1.2.3 Drain the water in the stage-one fuel filter.

4.1.2.4 Check the tension of belts, adjust it if necessary.

4.1.2.5 If the ambient temperature is less than 0

℃

, and the diesel engine is

not filled with antifreeze, drain the coolant to prevent the diesel engine
parts from being froze.

4.1.2.6 Check oil level in the fuel injection pump and governor, if needed,

refill it properly.

«
...
18
19
20
21
22
...
»

Содержание WP10






















































Отзывы:

Нет отзывов

Похожие инструкции для WP10

Бренд: Kohler Страницы: 84

Бренд: Kubota Страницы: 138

Бренд: Eurotronic Страницы: 4

Бренд: MSW Страницы: 159

Бренд: Kohler Страницы: 4

3T-MOTORS 3T35-R

Бренд: 3T-Components Страницы: 20

Бренд: Saito Страницы: 2

Бренд: Saito Страницы: 2

Бренд: Saito Страницы: 7

iSV2-CAN Series

Бренд: Leadshine Страницы: 107

Бренд: Champion Страницы: 22

Бренд: Sanyo Denki Страницы: 20

B&W S50MC-C8-TII

Бренд: Man Страницы: 403

Бренд: Toyota Страницы: 625

Бренд: Stiga Страницы: 161

Бренд: Ford Страницы: 40

Бренд: Seidel Страницы: 12

Бренд: Mitsubishi Страницы: 204

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды