manualshive.com logo in svg

WEG SSW900 Series, Руководство пользователя, Страница: 32 / 65

Поделиться
Скачать
WEG SSW900 Series Скачать руководство пользователя страница 32

FAULTS AND ALARMS

9 FAULTS AND ALARMS

Fault/Alarm

Description

Possible Causes

F129/A129:
Anybus Offline

It indicates communication interruption of Anybus-CC
accessory with network master.

- The master PLC went to the idle or programming
state.
- Programming error, the number of programmed I/O
words in the slave differs from the number adjusted in
the master.
- Lose of communication with the master (broken
cable, disconnected connector etc.).

F130:
Anybus Access Fault

It

indicates

access

error

to

the

Anybus-CC

communication module.
It actuates when the SSW cannot exchange data
with the Anybus-CC accessory, when the Anybus
module identifies some internal fault, or when there is
a hardware incompatibility.
In order to remove this fault, it is necessary to power
the SSW off and on again.

- Check that the accessory is properly fitted.
- Check that the equipment firmware version supports
the Anybus accessory.
- Hardware errors due to improper handling or
installation of the accessory, for example, may cause
this error.
- If possible, carry out tests by replacing the
communication accessory.

F132/A132:
Anybus Idle

It indicates that network master changed to idle or
programming state.

- How to detect this condition depends on the
communication protocol and the network master.

SSW900 | 32

Содержание SSW900 Series


































































Отзывы:

Нет отзывов