Weco HeSU 5K3-LV HV Скачать руководство пользователя страница 9

Страница: 9 / 69

WeCo 5K3-LV-HV

HeSU 5K3-LV HV

Page 9 of 69

V_1.1_21-Nov-2020_LV-HV

The mechanical installation method for the 5K3 LV-HV modules can be considered ‘’ conceptually’’ the

same for HV and LV configurations

The installer who intends to install the 5K3 LV-HV module in the HV configuration shall read this entire

manual including the HV configuration information included in Section-3 of this manual

SECTION-1: INSTALLATION & PRE-OPERATIONAL PROCEDURES

1.1 Module Handling and Lift Out from Box

The battery is always delivered in WALL mode and it is therefore necessary for the installer to make simple changes to
install the STACK kit. Below are the installation phases.

ATTENTION

The battery must be lift by 4 persons by using the 4 handles

2 Handles are inbuilt and the other two are provided as temporary handles to be used as shown below

Open the carton box, find the portable and retractable handles, position them and proceed with the lifting up.

Содержание HeSU 5K3-LV HV






































































Результаты поиска

Содержание HeSU 5K3-LV HV

Отзывы:

Бренды по названию

Популярные бренды

Weco HeSU 5K3-LV HV, Руководство пользователя

Результаты поиска

Содержание HeSU 5K3-LV HV

Отзывы:

Бренды по названию

Популярные бренды