background image

10

Cleaning work 

Use clear water for cleaning. Do not use flammable solvents. 

The vapors of the solvents may ignite upon contact with hot 

components or other sparks. 

Perform cleaning tasks only in rooms that are suitable and 

have been approved for that purpose. Residual oil and lubri-

cants that may have been rinsed off have a negative impact 

on the environment and must be collected by suitable means 

(e.g. oil separator). 

Safe handling of combustion 

engines 

Combustion engines pose a particular risk during operation.

Their exhaust emissions contain carbon monoxide, a colorless 

and odorless gas that is extremely hazardous, which, if inhaled 

even briefly, can cause unconsciousness and death.

Therefore, never inhale the exhaust gas.

Inspection

The machine must be inspected in accordance with the corre-

sponding implementation conditions and operating conditions 

to ensure its operationally safe status. This inspection should 

be performed as needed by an expert – however, no less than 

once a year. The findings of the inspection must be stored in 

writing until the time of the next inspection.

Содержание 0116144





























Отзывы:

Похожие инструкции для 0116144