1
SAFETY INSTRUCTIONS
RULES FOR SAFE OPERATION
1. Know your machine. Read and understand the
owner’s manual and labels affixed to the machine.
Learn its applications and limitations as well as the
specific potential hazards peculiar to this machine.
2. Grounding. This machine should be grounded while
in use to protect the operator from electric shock.
Machines which are designed to run on less than
150 volts are equipped with a 3 conductor cord and
3 prong grounding type plug to fit the proper
grounding type receptacle. The cord is long enough
that it should not be necessary to use extension
cords. Temporary extension cords and receptacle
adapters should be used only until a properly
grounded outlet can be installed by a qualified elec-
trician. Use only a 3 wire extension cord of ade-
quate size to handle the rated full load current of
the machine as indicated on the machine name-
plate. If an adapter is used to accommodate a 2
hole receptacle, the grounding ear must be at-
tached to a known ground. Never remove the 3
rd
prong (grounding blade) from the plug on the ma-
chine electrical cord.
3. Keep the machine guards in place and in good work-
ing order.
4. Avoid dangerous environments. Do not use the ma-
chine in a damp or wet location. Keep the work area
well lit.
5. Wear proper apparel. No loose clothing (i.e.
neckties) or jewelry to get caught in moving parts.
Wear protective covering to contain long hair.
6. Stay alert. Watch what you are doing. Use common
sense. Do not operate the machine when you are
tired. Do not use the machine after taking drugs, al-
cohol or medications.
READ ALL INSTRUCTIONS AND SAVE THEM FOR FUTURE
REFERENCE.
PURPOSE (GENERAL OVERVIEW)
WT-25LC and WT-25LCI series rewind machines are
made for the purpose of rewinding rolls of narrow web
products. In general, these are paper, film or foil prod-
ucts which are stiff enough to stand on edge (vertically)
throughout the web path of the machine. Cloth and
other woven materials generally do not rewind well (if
at all) on vertical spindle rewind machines. Abrasive
materials (sandpaper rolls, etc.) will damage the ma-
chine and should not be used. It is suggested that you
take a few minutes to become familiar with the controls
and operating characteristics before attempting to
rewind actual rolls.
WARNING
AS WITH ANY MACHINE, CAUTION MUST BE EXERCISED
TO PREVENT INJURY. NEVER OPERATE THE MACHINE
WITH GUARDS REMOVED. THE CONTROL CABINET
DOOR MUST BE KEPT CLOSED (SECURED BY SCREWS)
EXCEPT WHILE INTERNAL ADJUSTMENTS ARE BEING
MADE. ALWAYS EXPECT THE MOTOR TO TURN ON
WHEN THE START PUSHBUTTON IS OPERATED.
CAUTION
BEFORE CONNECTING THE MACHINE TO A SOURCE OF
ELECTRICAL POWER, OPEN THE CONTROL CABINET AND
VISUALLY INSPECT THE CONTROL PANEL TO BE SURE
THAT NO COMPONENTS OR WIRE CONNECTIONS HAVE
WORKED LOOSE IN SHIPMENT. WHEN INSPECTION IS
COMPLETE, CLOSE AND SECURE THE CABINET DOOR.
OPERATOR CONTROLS (WEB
TRANSPORT SYSTEM)
REWIND DIRECTION SWITCH
This switch determines the direction of rotation of the
rewind coreholder. When in the “PRINTING OUT” posi-
tion, the coreholder will turn in a counterclockwise di-
rection for winding with the labels on the outside of the
roll. In the “PRINTING IN” position, the rewind core-
holder will turn clockwise for winding labels on the in-
side of the roll.
MAIN SPEED CONTROL KNOB
Located next to the start pushbutton, the main speed
control knob is used to set the running speed before the
deceleration count is reached. Turning the knob clock-
wise will increase the speed. Rapid speed increases can
cause telescoping of the rewind roll and web breakage.
Therefore, the motor control has been pre-adjusted to
accelerate at an appropriate rate.
START PUSHBUTTON
Pressing of the START pushbutton will perform two
tasks. Most importantly, the motor control is enabled,
