WB Mfg 04068471 Скачать руководство пользователя страница 1

wibenchmfg.com

507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303

Specifications are subject to change. Product 

images are for illustrative purposes only and may 

differ from the actual product.

1

Elevate Student Desk

Assembly Instructions

04068471: -EJA

04068604: -ADJ

V021022  Version subject to change

Tools Required

• 

Screw gun

• 

4mm hex bit

• 

Phillips head 
screwdriver

• 

Drill bit extension

Before you begin, please make sure all parts and proper 

quantities are included. (See Part Identifier Key) Any parts 

damaged during shipment must be reported within 24 hours of 

receipt. To report information regarding damages or if you have 

any questions, please call 800.242.2303.

Step 1: 

 

•  Take base out of box and place on a protected flat surface.  
•  Insert center post into the base.

Base

Center Post

NOTE: 

These Assembly Instructions are based on the 

assembly of the Elevate Adapt XL (U.S. Patent D780487) 

Student Desk with an adjustable height base. Type and 

quantity of parts may vary depending on which desk or table 

is ordered. These instructions comply with all 

Elevate Student Desks. 

Содержание 04068471










Отзывы: