Wazer WAZER Main Unit Скачать руководство пользователя страница 67

Страница: 67 / 69

SECTION

Additional Resources

Customer Support

WAZER stands by its product, and we’re happy to help when you need assistance with setting up or
running WAZER.

We are constantly updating and putting out content that can aid in the setup, operation, and

troubleshooting of cutting with WAZER. If you can’t find what you are looking for within this

User Manual check our online resources at wazer.com/resources. There you will be able to find

information such as:

•

Troubleshooting & Maintenance

•

How-To Videos

•

WAZER Firmware and Config Files

•

Downloadable Updated User Manuals

WAZER Customer Support is here to provide help.

Visit wazer.com/resources or email us at [email protected].

Decommission, Disposal and Recycling of WAZER

Decommission

To properly bid farewell to your WAZER

WAZER is a tool that contain mechanical, electric and electronic components. Unregulated

disposal of such tools is strictly prohibited in many countries. Please consult your local electric

appliance recycling regulation, as well as this section, before starting to decommission your
WAZER.

Decommission Safety Precaution

To make sure that the high pressure system is relieved of its pressure, perform a nozzle purge

from the WAZER Control Panel by going to Setup & Maintenance > Maintenance > Nozzle Purge

before continuing with the rest of the steps.

Disassembly process

To avoid cuts, possible infection or particle inhalation, wear waterproof

protective gloves, facial mask and eye protection during the disassembly process.

Properly discard items mentioned in this section in accordance to local waste management

regulation. If regulation prohibits, put them aside for more instruction.

•

Drain the WAZER main unit.

•

Disconnect the Main Unit from its wall anchoring.

•

Follow the hose disconnect procedure printed on the safety label that is located on your

Main Unit and Pump Box. Discard all of the hoses.

•

Using the provided Cut Bed installation tool, remove the four Cut Bed bolts, and take the

Cut Bed out.

•

Cut Bed may contain cut material debris, consult your local waste management before

discarding it.

•

Clean used abrasive out of WAZER Main Unit tank. Leaving it dry for several days Will greatly

ease the cleaning process.

•

Completely dump all Dry Abrasive from the Abrasive drawer.

•

Cut the two power supply cables from Pump box and 24v power supply, discard them.

•

Unscrew pump box signal cable from pump box, cut it off from the Main unit, discard it.

•

Open Pump box cover, replace the yellow Pump Vent Cap with red Oil Cap. If lost, contact

WAZER for assistance. Put pump cover back on.

•

If you have a WAZER Stand-up, take the Stand Leg and Shelf off by reversing the process of

installing. Please refer to Stand Leg Accessory for installation process. Be mindful of every

safety precaution.

Information acquisition:

At this stage WAZER is decommissioned and ready for disposal. Every country and region has its

own laws, regulations and schemes regarding household electric appliances disposal or recycling.

Please contact your local relevant authorities or agencies for detailed information.

If local laws or regulations pose significant hurdles in disposal/recycling WAZER, or no existing

disposal/recycling scheme exist, contact WAZER customer service for assistance.

For EU (European Union) countries, decommissioned WAZER is regarded as Waste Electrical and

Electronic Equipment, thus law-abiding disposal or recycling procedure is enforced by law. Contact

WAZER customer service for assistance.

WAZER provides a free-of-charge collection program for any properly decommissioned and

disassembled WAZER units.

Prepare for transportation

•

If items described in “Disassembly” are prohibited from discarding by local laws and

regulations, you may put them inside the Main tank at this moment.

•

Use masking tape to secure movable parts, including Abrasive Hopper Drawer, Right Side

Access Panel, Front and Back Tank Cover, Door window. Tape 24V power supply at the

bottom Hoop.

If local authority or agencies provide door step collection service, prepare decommissioned WAZER

as they request, and disregard the following instructions.

If local authority or agencies do not provide a door step collection service, you then have to

prepare WAZER for transportation. Follow the following steps to safely package WAZER. Failure to

comply may result in refusal of acceptance, and extra cost incurred to you.

If you do not have the original packaging, please contact WAZER customer support, stating you are

looking for the return shipping package, we will ship it to you for your decommissioning process.

•

Retrieve the packaging material your WAZER came in, put the heavy duty cardboard base on

top of wooden pallet

•

Follow WAZER’s illustrated step by step guide as to how to package up a WAZER for

shipment here: WAZER.com/repair-instructions/repacking-wazer-for-shipping

WAZER is ready for the upcoming Transport.

Included in the price is a contribution to recycling costs.

126

127

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды