Wazer WAZER Main Unit Скачать руководство пользователя страница 22

Страница: 22 / 69

Water Connections

WAZER needs to be plumbed into your water lines. Here is a diagram of the system:

Installation has three steps:

•

Hose 1: Water Inlet Hose

(3/8” diameter White Hose)

•

Hose 2: Water Drain Hose

(1/2” diameter White Hose)

•

Hose 3: High-Pressure Hose

(Sturdy Black Hose)

Each hose is critical for operation. The Water Inlet Hose provides water for cutting. The Water

Drain Hose disposes water. The High-Pressure Hose delivers high-pressure water from the Pump

Box to WAZER. There are also several connections that cover other essential functions.

The provided Plumbing Kit should be compatible with most home or commercial plumbing. If the

supplied fittings are not sufficient, your local hardware store will have additional adapters and

connectors. If you are uncomfortable with this part of the setup, have a professional plumber

complete this part of the installation for you.

WAZER should never be configured to have its drain water recirculate into its Water

Inlet Hose. This will destroy the Pump Box and void your warranty. Visually check High-Pressure

Hose before installation. If the High-Pressure Hose outer layer has been damaged down to

the outer wire layer, the High-Pressure Hose shall be withdrawn from use. Contact WAZER for

replacement

Water Inlet Hose

Step

Water Drain Hose

Step

High-Pressure Hose

Step

Water Drain

Water Hook Up

Quick Connect System

We have provided a Push-to-Connect (“John Guest” style) system for both hoses.

This system requires no tools to lock or unlock hosing from the fittings. To lock the hose into the

fitting make sure the end of the hose is cleanly cut and push it into the fitting. When you push the

hose into the connector you will feel some resistance. Push past this resistance to fully seat the

hose. The resistance is from the fittings O-ring sealing around the hose.

Don’t be afraid to push forcefully to ensure you have fully seated the hose into the fitting.

To unlock the hose from the fitting, push the collet into the fitting and pull the hose out of the

fitting (in the opposite direction). Again, this may take some force.

Hose

QC Fitting

Collet

push in to release

O-Ring

Push Hose straight

in as far as it will go.

Hose is secured

in position.

Push in collet to

release Hose.

Hose

Collet

Set

tin

g Up W

AZER |

TION 4

Содержание WAZER Main Unit






































































Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды

Wazer WAZER Main Unit, Руководство пользователя

Результаты поиска

Содержание WAZER Main Unit

Отзывы:

Бренды по названию

Популярные бренды