Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 330

Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 91

Operation with touchscreen

4 Principles of operation

Krautkrämer USM 100

Rev. 9 (09/2023)

91

Settings

Many functions are parameters for which you can set a
value, for example the

Display Range

.

– Select the panel

Setup

and display the function

group

(see page 88). The functions and their

current settings are displayed.

– Tap on the function

Display Range

(1). The value se-

lector is displayed.

– Swipe the selector up or down to show the possible

values. The highlighted value in the center (3) is ap-
plied immediately without further saving. Depending
on the parameter, the effect is immediately visible in
the A-scan.

– Tap the calculator icon (2). A numeric keypad is dis-

played.

– Tap the digits to enter the required value.

– Tap

OK

(4) to complete the entry. The numeric key-

pad is hidden and the value is applied.

– Tap the function name (1) to close the value selector.

1

4

3

2

«
...
89
90
91
92
93
...
»

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов