Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 59

Страница: 59 / 330

USM 100 PC Live

3 Initial start-up

Krautkrämer USM 100

Rev. 9 (09/2023)

Establish connection

Prerequisite for the connection to the software

USM 100

is an existing network connection to the computer

via LAN (see page 269) or WLAN (see page 270).

– Install the software

USM 100 PC

on the computer.

– Check whether the USM 100 and the computer with

the software are connected to the same network.

– Tap the

Main menu

icon (see page 73) to display the

– Tap on the

If the

button is not visible, then an ap-

plication is currently loaded.

– In this case, tap the

Application desktop

button (see

page 68) and then tap the

Main menu

icon again.

Содержание Krautkramer USM 100










































































































































































































































































































































Результаты поиска

Содержание Krautkramer USM 100

Отзывы:

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 59 / 330

Результаты поиска

Содержание Krautkramer USM 100

Отзывы: