Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 49

Страница: 49 / 330

Power supply

3 Initial start-up

Krautkrämer USM 100

Rev. 9 (09/2023)

– Flip up the battery compartment cover and slide it

back to its original position until it is firmly closed.

– To remove the battery, open the battery compartment

as described above and carefully pull the battery out
by the tab (3).

Checking the charge level of the lithium-ion battery

The lithium-ion battery is provided with a battery charge
level indicator. Five squares (4) indicate the level of bat-
tery charge.

You can check the battery charge level before inserting
it into the instrument. If only one led is flashing, the
charge level is less than 10 %.

Содержание Krautkramer USM 100










































































































































































































































































































































Результаты поиска

Содержание Krautkramer USM 100

Отзывы:

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 49 / 330

Результаты поиска

Содержание Krautkramer USM 100

Отзывы: