Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 330

Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 25

Safety information

1 Introduction

Krautkrämer USM 100

Rev. 9 (09/2023)

25

FCC compliance

This device complies with part 15 of the FCC Rules. Op-
eration is subject to the following two conditions:

1

This device may not cause harmful interference.

2

This device must accept any interference received,
including interference that may cause undesired
operation.

This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial
environment.

This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful
interference to radio communications.

Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user
will be required to correct the interference at his own ex-
pense.

«
...
23
24
25
26
27
...
»

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов