Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 221

Страница: 221 / 330

Scan Setup

5 Operation

Krautkrämer USM 100

Rev. 9 (09/2023)

221

5.30 Scan Setup

In this function group you can set the parameters for the
B-scan and C-scan representations and the scanning
process.

Scan Pattern

You must select the scan pattern depending on the
scanner system you are using and the encoders in-
stalled.

Line

Only the scan axis is equipped with an encoder.

Bi - Dir Raster

Both the index axis and the scan axis are equipped with
an encoder. The scanning direction can be reversed.

Uni - Dir Raster

Both the index axis and the scan axis are equipped with
an encoder. Scanning is only possible in one direction.

Free Hand

Select this setting when a tracer scanner is used.

Single-Shot

This setting is not available for B-scan and C-scan.

Содержание Krautkramer USM 100










































































































































































































































































































































Результаты поиска

Содержание Krautkramer USM 100

Отзывы:

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 221 / 330

Результаты поиска

Содержание Krautkramer USM 100

Отзывы: