Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 176

Страница: 176 / 330

5 Operation

DAC

176

Rev. 9 (09/2023)

Krautkrämer USM 100

Turning the DAC evaluation off

You can turn the DAC evaluation off at any time.

– Set the function

DAC / TCG

Off

in order to hide the

curve.

Note

The DAC curve is not lost by turning the func-
tion off. By turning it on again, you can use
the function

DAC / TCG

to go back to the

DAC evaluation again without losing any set-
tings.

Deleting the DAC curve

You can delete the DAC curve at any time. After this, the
DAC evaluation is not possible until you have recorded
a new DAC curve.

– Tap the

Clear

icon in the Command bar (see

page 75). A confirmation message is shown.

– Confirm the deletion.

Содержание Krautkramer USM 100










































































































































































































































































































































Результаты поиска

Содержание Krautkramer USM 100

Отзывы:

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 176 / 330

Результаты поиска

Содержание Krautkramer USM 100

Отзывы: