manualshive.com logo in svg

Wavelength Electronics PLD K-CH Series, Техническое описание и руководство по эксплуатации, Страница: 10 / 24

Поделиться
Скачать
Wavelength Electronics PLD K-CH Series Скачать руководство пользователя страница 10

© 2020

www.teamWavelength.com

10

PLDXK-CH SERIES LASER DIODE DRIVER

WIRING THE PLD5K-CH AND PLD10K-CH (CONTINUED)

Figure 7.  Type C Laser Diode; PLD5K-CH and PLD10K-CH

LD Anode

LD Cathode

LD Enable

+5 V

GND

(Internally Shorted)

Analog Input

LIM I Monitor

LIM I Status

+

-

PD Cathode

Common

(Low Current)

PD

LD

OR

+

-

10µF

0.1µF

8 to 

12.5 VDC

LM 317

+5V REG.

732Ω

243Ω 1

3

2

330µF

0.1µF

This circuit shows how to use a single power supply.  

The LM317 (+5 V Regulator) circuit can be replaced 

with a separate 5 VDC power supply.

PD

LD

+5V

10 kΩ

Pull Up Resistor 

DMM

P Monitor

(PD Current)

I Monitor

(Output Current)

Optional External

Setpoint (0 to 5 V)

Short J3:5 to J3:1 when

analog input is not used.

J3:5

J3:1

or

J2:1

J2:4

J3:3

J2:3

J2:2

Jumper*

J3:4

H1:4

H1:2

H1:3

H1:1

J1:2

PDV J3:6

PD

Anode

PD Aux 

Out

J1:1

J3:2

* The External Jumper is installed only on the PLD5K-CH

and PLD10K-CH. The External Jumper is not installed on

the PLD12.5K-CH.

* A twisted-pair Power and LD Cable 

is available separately (WCB308)

Closed = Output Enabled

Open = Output Disabled

Figure 8.  Type A & B Lasers, Negative Power Supply Operation; PLD5K-CH and PLD10K-CH

J3:4

H1:4

OR

LD Anode

LD Cathode

H1:2

H1:3

LD Enable

Closed = Output Enabled

Open = Output Disabled

H1:1

+5 V

GND

(Internally Shorted)

J3:5

J3:1

or

J2:1

J2:4

J3:3

J2:3

J2:2

Analog Input

P Monitor

(PD Current)

I Monitor

(Output Current)

LIM I Monitor

LIM I Status

Optional External

Setpoint (0 to 5 V)

+

-

5 VDC

PD Anode

J1:1

0.1 µF

Common

(Low Current)

Short J3:5 to J3:1 when

analog input is not used.

PD

LD

PD

LD

DMM

10 kΩ

Pull Up Resistor

GND (Note 2)

+

-

Jumper (Note 1)

1. The External Jumper is installed only on the 

PLD5K-CH  and  PLD10K-CH.  The  External 

Jumper is not installed on the PLD12.5K-CH.

2. Isolate this ground connection from Earth if 

there  are  any  other  Earth-grounded 

components in the system.

* A twisted-pair Power and LD Cable 

is available separately (WCB308)

NOTE: For two-supply operation, it is critical to shut down the power supply to the laser first before shutting down the +5V 

supply powering the electronics.

Содержание PLD K-CH Series

























Отзывы:

Нет отзывов