background image

3

KLSC20-KLSC25-KLSC32-IM-DE-W-UK-08-2021-Rev.0 | Part no. 10084836

EN

ENGLISH

2  Safety

2.1  Safety notices

DANGER

DANGER indicates an imminent danger that

may cause serious physical injury or death if the appropriate 
safety precautions are not in place.

!

!

 

WARNING

WARNING indicates a danger arising through

incorrect behaviour (e.g. misuse, disregarding notices, etc.) 
that may cause serious physical injury or death.

!

!

 

CAUTION

CAUTION indicates a potentially dangerous

situation that may cause minor or slight injuries if the 
appropriate safety precautions are not in place.

NOTICE

NOTICE indicates a situation that may cause

material damage if the corresponding precautions are not 
taken.

2.2  Important safety information

•  Read this operating manual carefully before use.
•  Only connect this boiler charging unit to a power supply 

which matches the supply voltage stated on the boiler 
charging unit's data plate.

•  The power supply on the boiler charging unit must be 

disconnected before completing any maintenance, cleaning 
or repair work.

•  Maintenance, cleaning and repair work may be carried out 

by trained specialist personnel only.

•  If the boiler charging unit is damaged or is not functioning 

correctly, it must no longer be used. In this case, contact 
your specialist dealer immediately.

•  Observe the maintenance instructions and intervals.
•  Protect the boiler charging unit against the effects of 

weather.

•  Never use the boiler charging unit outdoors.
•  The boiler charging unit may only be used in accordance 

with its intended use.

2.3  Intended use

The boiler charging unit is used to reduce the time required 
to reach the boiler operating temperature (to avoid dropping 
below the dew point). This extends the service life of the boiler 
while also reducing the emission of harmful substances.
The boiler charging unit is fully pre-assembled and is designed 
for wall-mounting. The boiler charging unit is not intended for 
use by persons (including children) with reduced physical, 
sensory or mental capabilities, or lack of specialist knowledge 
or experience.

2.4  Foreseeable misuse

The following is regarded as foreseeable misuse:

•  operating the boiler charging unit contrary to the 

specifications;

•  using the boiler charging unit for use other than its intended 

use;

•  making modifications to the boiler charging unit not agreed 

with the manufacturer;

•  using replacement or wear parts not approved by the 

manufacture;

•  operating the boiler charging unit outdoors (parts and 

components are not UV-resistant).

2.5  Operator’s responsibility

The operator must ensure that:

•  the boiler charging unit is only used for its intended 

purpose;

•  the boiler charging unit is installed, operated and maintained 

according to the specifications in the Installation and 
Operating Manual;

•  the boiler charging unit is only operated according to local 

directives and occupational health and safety regulations;

•  all precautions have taken to avoid hazards originating from 

the boiler charging unit;

•  all precautions for first aid and fire suppression are carried 

out;

•  only authorised and trained users have access to and 

operate the boiler charging unit;

•  users have access to this Installation and Operating Manual 

at all times.

2.6 Users

Only qualified persons may operate the boiler charging unit or 
carry out service and maintenance work.

Operators

An operator is deemed to be qualified if they have read 
this operating manual and understood the potential hazards 
associated with improper behaviour.

Fitters/commissioners

Due to their technical training, expert knowledge and 
consideration of the relevant standards, provisions, regulations 
and laws, fitters/commissioners are able to carry out work on 
the boiler charging unit and to identify and prevent potential 
hazards.

Содержание KLSC Series















Отзывы: