Watts AMES LF685GD-20 Series Скачать руководство пользователя

Страница: 19 / 21

ES-A-ACV-LF985GD-20 2115

Issue

Possible Cause

Corrective Action

Notes

Main Valve will not
open

Closed isolation valves in pilot system.

Check isolation valves, ensure
open.

Insufficient supply pressure.

Check upstream pressure.

Depending on water
source, supply pressure
may not be controlled by
valve operator.

Main valve stem assembly corroded/
damaged

Inspect stem assembly, clean/
replace if necessary.

Blockage in pilot system.

Inspect & clean any installed
pilot system strainers, check
orifice/speed controls for
blockages.

Improperly configured opening speed
control.

Adjust opening speed control
to verify functionality, adjust as
required.

Standard setting for
opening speed control is
1

1/2

- 2

1/2

turns open from

full closed position. Can be
adjusted in field.

Main Valve will not
close

Closed isolation valves in pilot system

Check isolation valves, ensure
open.

Diaphragm is damaged

Conduct diaphragm seal test,
repair and replace if necessary.

Main valve stem assembly corroded/
damaged.

Inspect stem assembly, clean/
replace if necessary.

Blockage in main valve.

Perform freedom of movement
test; if valve does not close,
disassemble and remove
blockage.

Worn/damaged valve seat.

Perform seat sealing check;
disassemble and inspect/re-
pair seat if required.

Improperly configured closing speed
control.

Adjust closing speed control
to verify functionality, adjust as
required.

Standard setting for
closing speed control is
1

1/2

- 2

1/2

turns open from

full closed position. Can
be adjusted in field.

Solenoid will not
actuate

Possible Cause: Low or no voltage

Check voltage at the solenoid
connection, insuring that it has
the minimum of 85% of the
coils rated voltage.

Should be performed by
licensed electrician

Manual operated is engaged

Turn manual operator counter-
clockwise to disengage

Troubleshooting Guide

Installation, Operation and Maintenance - Series LF985GD-20

Содержание AMES LF685GD-20 Series






















Результаты поиска

Содержание AMES LF685GD-20 Series

Отзывы:

Похожие инструкции для AMES LF685GD-20 Series

Бренды по названию

Популярные бренды

Watts AMES LF685GD-20 Series, Руководство пользователя

Результаты поиска

Содержание AMES LF685GD-20 Series

Отзывы:

Похожие инструкции для AMES LF685GD-20 Series

Бренды по названию

Популярные бренды