Watts Aerco Modulex EXT Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 28

Watts Aerco Modulex EXT Series Скачать руководство пользователя страница 8

Modulex EXT Vent and Combustion Air Application Guide

Page 8 of

28

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, NY 10913

TAG-0054-0F

09/25/2017

Phone: 800-526-0288

GF-136-V

1.4.4.

Air Intake Connector (Supplied)

Air is drawn into the EXT through the air inlet on the left side of the unit (Figure 4). A connector is
included installed and ready to use for connecting the appropriate air intake piping for EXT 321–
1123/450–1100. For EXT 1530–3060/1500–3000, the combustion air intake adapter is shipped loose.
This adapter

is designed for spiral ducting only. For PVC ducting, order either P/N 58115-1 or 58115-

2 as per Table 1.

Figure 4: Air Intake Connection

NOTE:

See Chapter 3 for instructions for assembling the flue piping, including the exhaust manifold, Euro-to-
USA Adaptor, and Diameter Reduction Kits.

When using sealed combustion, observe the following requirements:

•

Sealed combustion is only available on the left of the unit only.

•

If using side-by-side minimum installation clearances, the center facing air inlet is not

available. See “Multi-Unit Installation Clearances (SD-A-968)” for further details.

Please note the following:

•

EXT Models 321 – 1123 are set up for PVC inlet piping.

•

EXT Models 1500 – 3060 come with an air intake adaptor for spiral ducting.

FOR EXT MODELS 321 – 1123

FOR EXT MODELS 1500 – 3060

«
...
6
7
8
9
10
...
»

Содержание Aerco Modulex EXT Series





























Отзывы:

Нет отзывов