Watts AERCO Benchmark OMM-0121 Скачать руководство пользователя страница 81

Страница: 81 / 164

Benchmark 750-3000 Boiler Operation & Maintenance Manual

APPENDIX A: BOILER MENU DESCRIPTIONS

OMM-0122_D

•

GF-206

•

5/9/2019

Technical Support

•

(800) 526-0288

•

Mon-Fri, 8 am - 5 pm EST Page 81 of 164

TABLE A-6: CALIBRATION MENU ITEM DESCRIPTIONS

See section 2-10 CALIBRATION Menu for a range of choices and the default values.

TABLE A-6: CALIBRATION Menu Item Descriptions

MENU OPTION

DESCRIPTION

Stepper Fbk

Allows the Air/Fuel Valve stepper motor feedback current to be calibrated at
the 0% (fully closed) and 100% (fully open) positions. Verification can also
be accomplished at the 50% position.

Purge Timer

Allows adjustment of the pre-ignition purge time.

Post Purge Timer

Allows adjustment of the purge time when a unit shuts down.

IGN Position

Allows adjustment of the valve position (Fire Rate) during the ignition
sequence.

Ign Pos Hold Tmr

FFWD Temp Disply

Enabled or Disabled.

Outlet Tmp Dsply

Enabled or Disabled.

Inlet Tmp Dsply

Enabled or Disabled.

Valv Pos Out Dsp

Enabled or Disabled.

Exhaust Tmp Dsp

Enabled or Disabled.

Exhaust Safety

Enabled or Disabled.

Flue Material

Select flue material: PVC, Polypropylene, or stainless

Exhst Fault Temp

Fault threshold temperature

Exhst Module Temp

Decreases Valve Position to lower exhaust temperature.

Exhst Warn Temp

Flue temperature high warning

Exhst Tmp VP Adj

VP adjust value

Exhst Adj Rate

VP adjust rate

VP Change Rate

VP Up Rate

Allows adjustment of the Valve Position (Fire Rate) increase rate when
raising the Valve Position. VP Up Rate is defined as Seconds per Step.

VP Down Rate

Allows adjustment of the Valve Position (Fire Rate) decrease rate when
lowering the Valve Position. VP Down Rate is defined as Seconds per Step.

Purge Blwr Offst

Allows adjustment of the blower speed (Blower Output Voltage) during the
Purge cycle.

4-20mA Purge Pct

Allows adjustment of the blower speed (Blower Output Voltage) during the
Purge cycle when using an Emerson VFD Drive to control the Blower Motor.

PWM In Adj

Allows the Pulse Width Modulation (PWM) duty cycle to be adjusted from -
5.0% to +5.0% in 0.1% increments.

Analog In Adj

Allows adjustment of the analog input from -5.0% to +5.0%.

Flow In Adj

Allows adjustment of the water Flow Rate Input from
-5.0% to +5.0%.

Содержание AERCO Benchmark OMM-0121





































































































































































Результаты поиска

Содержание AERCO Benchmark OMM-0121

Отзывы:

Watts AERCO Benchmark OMM-0121, Руководство по эксплуатации и обслуживанию, Страница: 81 / 164

Результаты поиска

Содержание AERCO Benchmark OMM-0121

Отзывы: