Watts AERCO 58025-05 Скачать руководство пользователя

Страница: 23 / 24

VD2: 10/14/14

Page 23 of 24

BMK1.5 LN Boiler 24-Month Maintenance Kit #58025-05 Instructions

Technical Instruction Document

TID-0066_0B

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

•

Phone: 800-526-0288

FINAL REASSEMBLY AND TESTING

Upon completion of all inspections and component replacement, reassemble the unit and
perform the tests specified in paragraphs 7.1 and 7.2.

7.1 Set-Up and Reassembly After Maintenance

Following completion of the all required inspections and replacements, perform the following

reassembly and setup procedures:

Setup and Reassembly After Maintenance Instructions

1. Ensure that the heat exchanger has been filled and the water supply and return valves

have been opened.

2. Turn ON the external circuit breaker to the unit.

3. At the front panel of the unit, set the

ON/OFF

switch on the C-More Control Panel to the

position.

4. Press the

LOW WATER LEVEL RESET

button to reset the low water cutoff.

5. Press the

CLEAR

switch to reset the fault relay. This will turn off the

FAULT

LED and clear

any displayed error message.

6. Replace the unit side panels and top panels.

7.2 Final Testing After Maintenance

Upon completion of the inspections and replacements specified in this Technical Service
Bulletin, perform the Combustion Calibration Tests specified in Chapter 4 of the O & M Manual
GF-120, GF-120M (Massachusetts only), or GF-121 (Dual-Fuel).

Following successful completion of the Combustion Calibration Tests, return the Benchmark
1.5LN Boiler to service use.

Содержание AERCO 58025-05

























Результаты поиска

Содержание AERCO 58025-05

Отзывы:

Похожие инструкции для AERCO 58025-05

Бренды по названию

Популярные бренды

Watts AERCO 58025-05, Технические инструкции

Результаты поиска

Содержание AERCO 58025-05

Отзывы:

Похожие инструкции для AERCO 58025-05

Бренды по названию

Популярные бренды