manualshive.com logo in svg

WattNode WNC-3Y-208-MB, Инструкция по установке и эксплуатации

Поделиться
Скачать
WattNode WNC-3Y-208-MB Скачать руководство пользователя страница 56

56 Specifications

Specifications

Models

Model

Nominal Vac 

Line-to-Neutral

Nominal Vac 

Line-to-Line

Phases

Wires

WNC-3Y-208-MB

120

208–240

3

4

WNC-3Y-400-MB

230

400

3

4

WNC-3Y-480-MB

277

480

3

4

WNC-3Y-600-MB

347

600

3

4

WNC-3D-240-MB

120*

208–240

3

3–4

WNC-3D-400-MB

230*

400

3

3–4

WNC-3D-480-MB

277*

480

3

3–4

*Note: the delta models have an optional neutral connection that may be used for measuring 
wye circuits. Delta models use the phase A and phase B connections for power.

Table 12: WattNode Models

Model Options

Any of these models are available with the following options. See the CCS website 

WattNode Modbus - Options

 page for details.

General Options

Option CT=xxx

:

 Pre-assign xxx as the global 

CtAmps

 value of the attached current 

transformers.

Option CT=xxx/yyy/zzz

:

 Pre-assign xxx to 

CtAmpsA

, yyy to 

CtAmpsB

, and zzz to 

CtAmpsC

. 

This is used if non-matching CTs are connected to different phases.

Communication Options

Option EP

:

 Factory configure the Modbus RS-485 communications to even parity (E81).

Parity:

 even

Data bits:

 8

Stop bits:

 1

Option 19K

:

 Factory configure the RS-485 communications 19,200 baud. Position 8 of the DIP 

switch will be ignored.

Option 38K

:

 Factory configure the RS-485 communications to 38,400 baud. Position 8 of the 

DIP switch will be ignored.

Option TCP-RTU

:

 Configure the communications to the Modbus TCP-RTU protocol option for 

use with RS-485 to Ethernet gateways (serial device adapters).

Option AD

:

 Factory configure the Modbus address. The DIP switch address will be ignored.

X Terminal Options

These options all utilize the 

X

 (auxiliary) terminal on the 

MODBUS

 connector:

Option X5

:

 Provides 5 Vdc at up to 60 milliamps between the 

C

 (common) and 

X

 (5V) terminals.

Output Voltage:

 5 Vdc ± 5%

Minimum Output Current:

 0 mA

Maximum Output Current:

 60 mA

Maximum Short-Circuit Output Current:

 150 mA

Recommended Maximum 5V Wire Length:

 30 cm (1 foot)

Содержание WNC-3Y-208-MB































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды