manualshive.com logo in svg

Watt Stopper UT-300-1, Руководство по установке, Страница: 10 / 13

Поделиться
Скачать
Watt Stopper UT-300-1 Скачать руководство пользователя страница 10

Override: Switch 2

To override all sensor functions, set DIP switch 2 to the ON position. The green LED 
comes on and stays on for the duration of the override.

This bypasses the occupancy detection control functions of the sensor, but still 
allows the lights to be manually controlled with a light switch, if one is installed.

Time Delay: Switches 3, 4, 5

The sensor will hold the lights on as long as occupancy is detected. The time delay 
countdown starts when no motion is detected. After no motion is detected for the 
length of the time delay, the sensor will turn the lights off. The sensor can select the 
time delay using SmartSet, or you can select a fi xed time delay.

•  SmartSet records occupancy patterns and uses this history to choose an optimal 

time delay from 5 to 30 minutes. SmartSet behavior starts immediately and is 
refi ned continually as history is collected.



Walk-through mode turns the lights off three minutes after the area is initially 
occupied, if no motion is detected after the fi rst 30 seconds. If motion continues 

beyond the fi rst 30 seconds, the selected time delay applies. 

LED: Switch 6

When enabled, the green Ultrasonic Activity LED on the sensor will light when the 
sensor detects motion.

Call 800.879.8585 for Technical Support

Содержание UT-300-1














Отзывы:

Нет отзывов