Watson-Marlow 630 U Скачать руководство пользователя страница 52

Страница: 52 / 186

14.3

IP31 Wiring connections

RJ45 connections

Connect an RJ45 (CAT5 or above, shielded recommended) network cable from the PC to the pump
connection port 1 or 2.

LED 1

LED 2

RX-

RX+

TX-

TX+

LED 1

LED 2

Indication

Low

Off

Low

High

Yellow LED on for link detected, flickers to indicate 10 Mbit activity

High

Low

One green LED on for link detected, flickers to indicate 100 Mbit activity

High

Two green LEDs on for link detected, flickers to indicate 1Gbit activity

14.4

Sensor Wiring - IP31

Standard - 9 way D - Sensor connector (Female/Chassis Skt)

Recommended control cable: 7/0.2mm 24AWG screened, circular. The cable screen should be earthed
with a 360 deg connection to a conductive back-shell.

AN-IP1

UNASSIGNED

AN-IP2

OP_ST

LEAK

FREQ

EAR

GND

Wiring the 9 way D sensor connector

m-630un-en-08

Содержание 630 U



























































































































































































Результаты поиска

Содержание 630 U

Отзывы:

Похожие инструкции для 630 U

Бренды по названию

Популярные бренды

Watson-Marlow 630 U, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 630 U

Отзывы:

Похожие инструкции для 630 U

Бренды по названию

Популярные бренды