Watson-Marlow 630 U Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 186

background image

26.1

Leak detection

If a Watson-Marlow leak detector has been fitted to the pumphead, and a leak is detected; the pump will
display the following message:

Follow the instructions in

"Tube replacement " on page 167

to replace your tube or tubing element.

If this message is repeated when power is returned to the pump check that the leak detector is clean and
free of debris and cycle the power to the pump.

Note

: The message will continue to be displayed unless the leak is cleared and the acknowledge key is

pressed.

26.2

Error codes

If an internal error occurs, an error screen with a red background is displayed. Note: Signal out of
range, over signal and leak detected error screens report the nature of an external condition. They do
not flash.

Error code

Error condition

Suggested action

Er 0

FRAM write error

Attempt to reset by switching power OFF/ON. Or seek
support.

Er 1

FRAM corruption

Attempt to reset by switching power OFF/ON. Or seek
support.

Er 2

FLASH write error during drive update

Attempt to reset by switching power OFF/ON. Or seek
support.

Er 3

FLASH corruption

Attempt to reset by switching power OFF/ON. Or seek
support.

Er 4

FRAM shadow error

Attempt to reset by switching power OFF/ON. Or seek
support.

Er 9

Motor stalled

Stop pump immediately. Check pumphead and tube.
Power OFF/ON may reset. Or seek support.

Er10

Tacho fault

Stop pump immediately.
Power OFF/ON may reset. Or seek support.

m-630un-en-08

161

«
...
159
160
161
162
163
...
»

Содержание 630 U



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 630 U

Бренд: Sanden Страницы: 26

Бренд: SAHP Страницы: 41

Бренд: Eccotemp Страницы: 90

Бренд: Eccotemp Страницы: 40

Бренд: Eccotemp Страницы: 19

Бренд: Radiant Страницы: 8

Бренд: UGSI Страницы: 125

Бренд: KISANKRAFT Страницы: 44

Бренд: German pool Страницы: 17

Бренд: Annovi Reverberi Страницы: 4

Бренд: Geotech Страницы: 32

Бренд: Zenit Страницы: 24

Zoneline AZ91H18E E Series

Бренд: GE Страницы: 78

Hydra-Cell G-25

Бренд: Wanner Engineering Страницы: 20

Бренд: Oase Страницы: 179

Husky 307 F Series

Бренд: Graco Страницы: 36

Бренд: Alfa Laval Страницы: 59

Бренд: Biral Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды