Watson-Marlow 630 U Скачать руководство пользователя страница 150

Страница: 150 / 186

Your selected language will now be displayed on screen. Press

CONFIRM

to continue, all displayed text

will now appear in your chosen language.

Press

REJECT

to return to the language choice screen.

MODE menu

Selecting

MODE

menu from the main menu will navigate you to access the sub-menu shown below. This

is the same as pressing the

MODE

key. Please see

"Mode menu" on page 1

for further details.

24.3

Control settings

Select

CONTROL SETTINGS

from the main menu to access the sub menu shown below. Use the

∧

∨

keys

to move the selection bar. Press

SELECT

to choose the required function.

Speed limit

The maximum speed the pump is capable of running at is 265rpm.

Select

Speed limit

from the control settings menu to define a lower maximum speed limit for the

pump.

This speed limit will be applied to all operating modes.

Use the

∧

∨

keys to adjust the value and press

SAVE

to set.

150

m-630un-en-08

Содержание 630 U



























































































































































































Результаты поиска

Содержание 630 U

Отзывы:

Похожие инструкции для 630 U

Бренды по названию

Популярные бренды

Watson-Marlow 630 U, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 630 U

Отзывы:

Похожие инструкции для 630 U

Бренды по названию

Популярные бренды