Watson-Marlow 630 U Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 186

background image

PIN entry on start-up

The setting

PIN entry during start-up

can be used to configure the software to choose if PIN entry is

required during start up.

This feature also means that auto-restart capability is now independent of PIN code entry after start up.

If this setting is enabled

ü

then the pump will require the PIN code to be entered before the pump will

enter the home control screen after a power cycle.

If this setting is disabled

û

then the pump will not require the PIN code to be entered before the pump

will enter the home control screen after a power cycle.

The auto-restart response of the pump after a power cycle is now independent of PIN entry.

The default setting, is enabled

ü

so a PIN code will be required after a power cycle before the pump will

enter the home control screen.

Disabling this feature does not change any other aspects of PIN code operation. Anyone wishing to
modify pump settings will still need to enter the PIN code.

24.2

General settings

To view the general settings menu, select

GENERAL SETTINGS

from the main menu.

Auto restart

This pump includes a feature called auto restart. This setting only applies to pump operation in manual
mode, network mode and memodose mode. This setting only applies to pump operation in manual
mode.

If the pump is operating in any of these modes and this feature is enabled (configured to 'yes'), it will
change the way the pump responds to a power cycle.

If the pump is operating in manual mode and this feature is enabled (configured to 'yes'), it will change
the way the pump responds to a power cycle.

When Auto restart is enabled it will cause the pump to remember it's current operating settings when
power is lost and to resume using these as soon as power comes back on.

This parameter only affects manual mode, network mode and memodose mode operation.

The '!' symbol is also displayed when the auto restart feature is enabled to warn users that the pump has
been configured in a way that could result in unexpected operation.

140

m-630un-en-08

«
...
138
139
140
141
142
...
»

Содержание 630 U



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 630 U

Бренд: Barnes Страницы: 12

Бренд: A.O. Smith Страницы: 8

Water Solutions 3098 Series

Бренд: Zoeller Страницы: 4

Aquanot Spin 508

Бренд: Zoeller Страницы: 2

Бренд: Zoeller Страницы: 11

Бренд: Zip Страницы: 18

Бренд: DAXOM Страницы: 20

GOULDS e-SVI Series

Бренд: Xylem Страницы: 40

Gyre 300 Series

Бренд: Maxspect Страницы: 164

Бренд: Serenity Страницы: 3

Бренд: Gardena Страницы: 17

Бренд: MARNEX Страницы: 28

Бренд: SUN HoM Страницы: 17

Бренд: Becker Страницы: 6

ecoFIT pure 825

Бренд: Vaillant Страницы: 48

Бренд: Oase Страницы: 31

Бренд: Oasis Страницы: 40

Бренд: DAB Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды