Watson Marlow Pumps 603R Скачать руководство пользователя страница 2

 

2

 

Declarations 

 

Declaration of 
conformity

  

 

When this pump unit is used as a stand alone pump it complies with: Machinery 
Directive 98/37/EC EN60204-1, Low Voltage Directive 73/23/EEC EN61010-1, EMC 
Directive 89/336/EEC, EN50081-1/EN50082-1. 

 

Declaration of 
Incorporation

 

When this pump unit is to be installed into a machine or is to be assembled with other 
machines for installations, it must not be put into service until the relevant machinery 
has been declared in conformity with the Machinery Directive 98/37/EC  EN60204-1.

 

 
Responsible person: Dr R Woods, Managing Director, Watson-Marlow Limited, Falmouth, Cornwall TR11 4RU, 
England. Telephone 01326 370370  Fax  01326 376009. 

 

Two year warranty 

Watson-Marlow Limited warrants, subject to the conditions below, through either Watson-Marlow Limited, its 
subsidiaries, or its authorised distributors, to repair or replace free of charge, including labour, any part of this product 
which fails within two years of delivery of the product to the end user. Such failure must have occurred because of 
defect in material or workmanship and not as a result of operation of the product other than in accordance with the 
instructions given in this manual. 

Conditions of and specific exceptions to the above warranty are: 

• 

Consumable items such as tubing and rollers are excluded. 

• 

Products must be returned by pre-arrangement carriage paid to Watson-Marlow Limited, its subsidiaries, or its 
authorised distributor. 

• 

All repairs or modifications must have been made by Watson-Marlow Limited, its subsidiaries, or its authorised 
distributors or with the express permission of Watson-Marlow Limited, its subsidiaries, or its authorised distributors. 

• 

Products which have been abused, misused, or subjected to malicious or accidental damage or electrical surge are 
excluded. 

Warranties purporting to be on behalf of Watson-Marlow Limited made by any person, including representatives of 
Watson-Marlow Limited, its subsidiaries, or its distributors, which do not accord with the terms of this warranty shall not 
be binding upon Watson-Marlow Limited unless expressly approved in writing by a Director or Manager of Watson-
Marlow  Limited. 

Information for returning pumps 

Equipment which has been contaminated with, or exposed to, body fluids, toxic chemicals or any other substance 
hazardous to health must be decontaminated before it is returned to Watson-Marlow or its distributor. 

A certificate included at the rear of these operating instructions, or signed statement, must be attached to the outside 
of the shipping carton. 

This certificate is required even if the pump is unused. If the pump has been used, the fluids that have been in contact 
with the pump and the cleaning procedure must be specified along with a statement that the equipment has been 
decontaminated. 

Safety 

In the interests of safety, this pump and the tubing selected should only be used by competent, suitably trained 
personnel after they have read and understood this manual, and considered any hazard involved. 

Any person who is involved in the installation or maintenance of this equipment should be fully competent to carry out 
the work. In the UK this person should also be familiar with the Health and Safety at Work Act 1974. 

 

 

There are dangerous voltages (at mains potential) inside the pump. If access is 
required, isolate the pump from the mains before removing the cover.

 

 

Содержание 603R














Отзывы: