Watlow Electric Gateway & DeviceNet Скачать руководство пользователя

Страница: 1 / 21

RUI/Gateway & DeviceNet

Configuration & Ladder Logic Example

Using an Allen-Bradley CompactLogix PLC

Watlow
1241 Bundy Blvd
Winona, MN 55987
Telephone: 507-494-5656
© 2007 Watlow Electric Mfg Co 1

4/08

Configuring the RUI/Gateway on DeviceNet

Using RSNetWorx

Prior to making the physical connections on the network setup the gateway DeviceNet

communications parameters per your network requirements, i.e., baud rate and node

address. If your not sure how to do this go to

http://www.watlow.com

and download the EZ-

ZONE

PM Communications Manual and follow the procedure defined in the DeviceNet

chapter.

Once the gateway communications parameters for DeviceNet

are set according to your

network requirements connect the gateway into the network and do the following:

a. Run RSLinx software and configure the driver of choice

b. Run RSNetWorx software.

As shown below (within RSNetWorx software), click on the online command from the tools
toolbar and then select the appropriate communications path to browse the DeviceNet

network. Set up in previous step using RSLinx software.

After successfully browsing the network all nodes on the network will appear in the graphical

Содержание Gateway & DeviceNet






















Результаты поиска

Содержание Gateway & DeviceNet

Отзывы:

Похожие инструкции для Gateway & DeviceNet

Бренды по названию

Популярные бренды

Watlow Electric Gateway & DeviceNet, Конфигурация

Результаты поиска

Содержание Gateway & DeviceNet

Отзывы:

Похожие инструкции для Gateway & DeviceNet

Бренды по названию

Популярные бренды